Battling Electrical Noise in CNC builds

 Electrical Noise in CNC builds

I recently posted my design guidelines for electrically noiseless builds on another blog and am sharing it here.
https://donsthings.blogspot.com/2018/09/battling-electrical-noise-in-cnc-builds.html

Donate:

Please consider donating (button to the lower left of this post).
Your donations help fund additional research, experiments, designs, tools and parts that I will return to the community as information.


Enjoy and comment,

Don

Comments

  1. keerthiroyMay 24, 2019 at 11:24 PM

    very informative artical,If you are eager to join your career in Cnc Programming Course then Cnc Training Center In Coimbatore is the best choice for you, where they can provide the best Training.

    ReplyDelete

Post a Comment

Popular posts from this blog

OX 48V spindle control

Image
Background DRAFT WORK IN PROGRESS One of the first steps in setting up the OX for operation is to calibrate the spindle speed vs the "M3" values sent from the TinyG. My first set of tests revealed a non-linearity in this control function. https://plus.google.com/+DonKleinschnitz/posts/AG6gZ7Lxhs7 This caused me to start a search to find, explain and remove the spindle vs speed linearity, the subject of this post. Donate: Please consider donating (button to the left bottom of this post). Your donations help fund additional research, tools and parts that I will return to the community as DIY information. Circuit tracing The Rio Rand controller was dissembled and a schematic was created. Theory of operation The key elements of the controller's design are: PWM input source choices: external or internal generated PWM selected by jumper External PWM: an opto-coupler interfaces the external PWM to the 555 which in this mode is used as a pre-st...
Read more

Building a Table for the Ox

Image
The DOX (Don's OX) Table Build Finally all CNC's in one place in my shop. Both laser and Router are on movable bases Goals: Strong  Sits on the floor when in operation but can be moved easily Houses electronics Room for a hood added at a later time Space for electronics Design: Materials: dimensional lumber from big box stores 3/4" MDF thick top Integrated lift: lifts entire table up on casters for movement Storage space  Space for drawers, electronics, PC or tablet General Parts Frame parts: 2x4 and 2x6, 96" length Cam lags: 1/2 x 6" and flat washer. Most other hardware: 1/4 x 5" lag screws and washers Top: 3/4 MDF, size to your liking Shelf: 1/4" fiber board or material to your liking A rough cut-list for the V3 model below Initial Build Complete The table cut and kitted 1/2 x 6" lag screws in cams 1/2 x 6" lags were used in the cams so that the non threaded part of the shaft crea...
Read more

Wiring the OX

Image
Wiring Phase & Diagrams I like to start the wiring phase with a schematic of the overall build interconnections. These are helpful starter links; TinyG "Getting Started" LitePlacer's blog Wiring Cable routing Wiring Schematic (a work in progress) Endstop Wiring From the Synthetos forum: Wire the limit switches between the ground and the switch inout – e.g. Xmin, Xmax, Ymin… Note if the switch is Normally Open (NO) or Normally Closed (NC) and set the $st setting for the proper switch type. All switches must be the same type. We recommend NC switches as they provide better noise immunity from false triggers. You will want to pay attention to switch wiring, as the wiring can pick up noise and fire if not done well. The RC circuits described above help a lot, but motor or spindle noise can creep in. The best strategy is to use twisted pair shielded cable. I have found guitar pickup cable to work well as it is all that plus it’s very small and fl...
Read more